Biasi Boilers

Compare Biasi boilers including combi, regular and system boilers and gas, oil and electric boilers.

For competitive prices, click on the button below to get boiler quotes for a new boiler installation.

Biasi

Biasi Boilers - Get Boiler Quotes

Biasi Combi Boilers

Biasi combi boilers deliver rapid access to hot water from the mains water supply by means of a wall mounted units with a small footprint that are commonly located in a kitchen or bathroom and concealed within a cupboard. Biasi combi boilers are cost efficient units with affordable heating costs that are ideally suited to apartments and small to medium sized houses with 1 to 2 bathrooms. Biasi combi boilers don’t require hot water tanks or cylinders as a regular boiler or system boiler does therefore making these Biasi combi boilers lower cost to install.
BoilerEfficiencyOutputWarrantyMPNBoiler Type
Biasi Advance 25kW Gas Combi Boiler88.7%25kW5 YearsCombi
Biasi Advance 30kW Gas Combi Boiler89%30kW5 YearsCombi
Biasi Advance 35kW Gas Combi Boiler89%35kW5 YearsCombi
Biasi Advance Plus 7 25kW Gas Combi Boiler92%25kW7 YearsCombi
Biasi Advance Plus 7 30kW Gas Combi Boiler92%30kW7 YearsCombi
Biasi Advance Plus 7 35kW Gas Combi Boiler92%35kW7 YearsCombi
Biasi Advance Plus ErP 25kW Gas Combi Boiler88.7%25kW5 YearsCombi
Biasi Advance Plus ErP 30kW Gas Combi Boiler88.6%30kW5 YearsCombi
Biasi Advance Plus ErP 35kW Gas Combi Boiler88.6%35kW5 YearsCombi
Biasi Inovia ErP 25kW Gas Combi Boiler88.7%25kW5 YearsCombi
Biasi Inovia ErP 30kW Gas Combi Boiler88.6%30kW5 YearsCombi
Biasi Inovia ErP 35kW Gas Combi Boiler88.6%35kW5 YearsCombi
Biasi Riva Plus ErP 24kW Gas Combi Boiler88%24kW2 YearsCombi
Biasi Riva Plus ErP 28kW Gas Combi Boiler88%28kW2 YearsCombi

Biasi System Boilers

BoilerEfficiencyOutputWarrantyMPNBoiler Type
Biasi Advance 25kW Gas System Boiler89%25kW5 YearsSystem
Biasi Advance 30kW Gas System Boiler89%30kW5 YearsSystem
Biasi Advance Plus 7 25kW Gas System Boiler92%25kW7 YearsSystem
Biasi Advance Plus 7 30kW Gas System Boiler92%30kW7 YearsSystem
Biasi Advance Plus 7 35kW Gas System Boiler92%35kW7 YearsSystem
Biasi Advance Plus ErP 16kW Gas System Boiler88.7%16kW5 YearsSystem
Biasi Advance Plus ErP 25kW Gas System Boiler88.8%25kW5 YearsSystem
Biasi Advance Plus ErP 30kW Gas System Boiler88.7%30kW5 YearsSystem
Biasi Inovia ErP 25kW Gas System Boiler88.8%25kW5 YearsSystem
Biasi Riva Plus ErP 24kW Gas System Boiler88%24kW5 YearsSystem
Biasi Riva Plus ErP 28kW Gas System Boiler88.1%28kW2 YearsSystem

Biasi Regular Boilers

BoilerEfficiencyOutputWarrantyMPNBoiler Type
Biasi Advance OV 15kW Gas Regular Boiler92%15kW5 YearsRegular
Biasi Advance OV 18kW Gas Regular Boiler92%18kW5 YearsRegular
Biasi Advance OV 24kW Gas Regular Boiler92%24kW5 YearsRegular
Fault CodeFault ImageSystem Behaviour
ER 01 + ResetN/ALack of burner ignition on safety lockout
ER 02 + ResetN/ASafety thermostat intervention lockout
ER 03 + ResetN/AGeneral lockout
ER 04 +
Faulty primary circuit (no water or absence of flow)
ER 05 +
Faulty fan control system
ER 06 +
Faulty c.h. temp. probe NTC
ER 07 +
Faulty d.h.w. temp. probe NTC
ER 08 +
Faulty external temp. probe NTC
ER 09 +
Faulty flue temp. probe NTC
ER 10 + resetN/AFlue probe intervention lockout
N/A
Flame detection error (An flashing + number error flashing
ER 12 +
Faulty central heating temperature probe NTC
ER 13 +
DT Delivery return >40k
ER + 14 + ResetN/AFaulty pump or primary temperature above 105°C
ER + 14 + ResetN/AFaulty pump or primary temperature above 105°C
ER + 14 +
Absence of flow from temperature gradient (>2K/s)
ER + 19 +
Domestic hot water inlet probe failure (if sent)
ER + 25 + ResetN/AFlame detection fault
ER + 69N/AWiring fault lockout
LiN/APrimary circuit temp. limit during d.h.w. operation
N/ABoiler Stand-By, hyphens are turned on in sequence to simulate running /antifreeze protection activated)
N/A
Boiler Stand-By, hyphens are turned on in sequence to simulate running /antifreeze protection activated)
N/A
Filling request: The boiler works regularly and the display shows all the icons, but the signal FL is flashing every 1 sec.
N/A
Insufficient pressure: The boiler stops displaying the water lack error.
30cN/ABoiler waiting for heat request
N/A
Boiler in summer mode (d.h.w.). The primary circuit temperature is displayed.
N/A
Boiler in winter mode (c.h.+ d.h.w.) The primary circuit temperature is displayed.
N/A
Boiler on demand for d.h.w. power. The d.h.w. temperature is displayed. / Boiler on demand for c.h. power.
N/A
Burner ignition (spark)
N/A
Flame present (Burner on)
N/A
Pre-heating function 3 stars DHW comfort. This information is not displayed. It will be possible to check its state in the section “INFO” value “cF” (the signal “cF” is alternated to the CH temperature value until the end of this function). You can enter the function pushing the buttons 12 and 13 together. The function is confirmed showing ON or OFF alternating for 5 sec. This function is always active at every hour (it’s not possible to set the time slots unless a remote control is connected).
N/A
Pre-heating function 3 stars DHW comfort. This information is not displayed. It will be possible to check its state in the section “INFO” value “cF” (the signal “cF” is alternated to the CH temperature value until the end of this function). You can enter the function pushing the buttons 12 and 13 together. The function is confirmed showing ON or OFF alternating for 5 sec. This function is always active at every hour (it’s not possible to set the time slots unless a remote control is connected).
N/A
Boiler in anti-freeze phase (bP flashing + temperature flashing)
N/A
Boiler in antifrost phase (AF flashing + temperature flashing)
N/A
Set c.h. (all other symbols are disabled)
N/A
Remote control connected – 1 flash every 4 seconds
N/A
Set d.h.w. (all other symbols are disabled)
N/A
Pump activated for the post-circulation phase (Po flashing + temperature flashing)
N/A
Delayed burner ignition for setting the system (uu flashing + temperature flashing)
N/A
Maintenance required The wrench symbol is flashing (without showing any error)
LPN/ABoiler in chimney sweep in function. The activation of the chimney sweep occurs configuring the “parameter P09=01” and is visualized: LP= minimum dhw hP= minimum heating cP= maximum heating dP= maximum dhw. The transition occurs with keys 16 (increase) and 15 (decrease) dhw temperature. The writing on the display alternates.
N/A
Boiler in chimney sweep in function. The activation of the chimney sweep occurs configuring the “parameter P09=01” and is visualized: LP= minimum dhw hP= minimum heating cP= maximum heating dP= maximum dhw. The transition occurs with keys 16 (increase) and 15 (decrease) dhw temperature. The writing on the display alternates.
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.